Repair Netgear Wireless Router And Westell Modem + Router = Routed Bridge Failure (Solved)

Home > Netgear Wireless > Netgear Wireless Router And Westell Modem + Router = Routed Bridge Failure

Netgear Wireless Router And Westell Modem + Router = Routed Bridge Failure

Within hours, all my computers on the LAN-side of the Netgear were reprogrammed to 10.0.0.1/24 IP addresses. It was easy to scroll down the Source column and find where the IP address switched about 21632 seconds into the log. Sadly this device has no ADSL modem built into it - for that I am using a N300 (cheapest I could find) as an ADSL bridge.My throughput after putting all of SUCH BS! have a peek here

If you're interested, you can read about the murder of an Iranian computer expert trying to purge this worm out of their nuclear power plants. The point is, you're basically on your own and your Internet provider won't support you if you don't use their devices That said, here's what I did. Comment by SMB -- November 17, 2009 @ 11:40 am The post is now out-of-date for my personal setup, as the netgear in question got replaced by a faster router. I just damaged ONE.

With the Westell in bridge mode, I was unable to get to its configuration page from behind the Netgear, and I would have to take the Netgear out of the network The Westell page told me a great deal of information about the DSL connection, since the device doubled as a modem, and it was a minor annoyance to not be able Perhaps I've been lucky, but it's been really solid.Brad - Double NAT? I can disconnect the cat5 and still have FIOS TV, but no internet.

At the end, if you have a computer that is to be connected to a router, then connect it to the router using ethernet cable. STARTING IP adress to 10.10.10.100. Tags: computers, networking, Sci/Tech Comments (12) 12 Comments nice summary. Most older DSL modems are bridge mode only and do not have advanced firmware to allow them to do DHCP and PPPoE.

Then you're double NATting, and the main problem people have with the AT router is the crappy NAT table. Filed under: Sci/Tech -- PolitiCalypso @ 4:10 pm Do a web search for "how to use two routers on a home network" or something similar, and the overwhelming majority of the that's it. http://forums.techguy.org/networking/927868-netgear-wireless-router-westell-modem.html I would like to do this for no other reason than the ‘side benefit' you mention.

You come off as exceedingly callous to that fact. router ip to 192/168.7.1 and it should workHope this helps.Rick Flag Permalink This was helpful (0) Collapse - ADSL +Netrgear Wireless router by deepika_aman / August 30, 2006 10:49 PM PDT From reading some of the other issues, I'm wondering if my WEP security could be the problem. Navigate to http://192.168.10.1, login, and set the wireless settings as directed in the setup guide.My error was that I incorrectly overrode the router basic setting for "Does you Internet Service requuire

I just setup a bridge in my home for entirely different reasons. see it here Mary,First, if you can connect via ethernet cable, then changing your IP address will not help you, matter of fact, it may cause you to lose your connection, hard to say Consult the Netgear Technical Support Page for your particular router setup. It works, I promise.

Router #1 is a brand new ZyXEL P-2601HN-F1 that my ISP provided, router #2 is an older one, TP-LINK TL-WR64xG(x=1 or 2). navigate here Additionally, all the DHCP ranges and reserved addresses inside the Netgear router were reset to 10.0.0.0/24 addresses. Or any other way? There must be a way around this, right?

Set it to automatic Configuration DHCP (it is the default but make sure it is). It appears they culled admin passwords to the router, and modified my router settings. NOTE: It may be possible to call your installer and have your ONT changed to use RJ-45, but Coax is the default for almost every installation I've seen. Check This Out REALLY?

Thanks See more Ip address 10.10.10.100 causing internet disconnect 198.168.1.254 Connecting to internet after connecting router to att modem Problem with AT&T Modem and Linksys Router Problem w/Motorola Modem and Linksys It's spendy, but works fantastically and is worth the premium. Report markytoon- Jun 17, 2009 03:20PM Thank you for your efforts, but this still didn't work for me.

However- older firmwares of the Westell ethernet/USB modem (especially 2100 and 2200) WILL NOT match this article.2008-03-25 22:14:26 got feedback?

I used to do a lot of work with PLC and SCADA devices (computers used to control hardware in the real physical world). The one listed "computer" on My Network below is one device Verizon should see: the Netgear router. Write down all IP addresses listed that are in the 192.x.x.x range (i.e. I wanted to give what you tried a shot but am wondering how it was that you chaged your router ip?

Network topology came up in some dicussions. Read on. 1st Amendment Congress shall make no law respecting an establishment of religion, or prohibiting the free exercise thereof; or abridging the freedom of speech, or of the press; or I added a gigabit switch to partition things, but this router remains a weak part of the network. this contact form There are reasons for why it was necessary to have it act with its full functionality.

I feel that we still are under that "bridge mode" but not getting an IP address as we did we before, I had to statically assign an IP to my router, However, I have to use "Automatic Configuration - DHCP" in my linksys WRT54G Version 5 to make it works. Click here for more information. •If you encounter any problems simply reset the Westell, connect it directly to your NIC, restart your computer, log into the Westell interface, and start over