Repair New Computer Toruble Tutorial

Home > Pc Build > New Computer Toruble

New Computer Toruble

Contents

If it is shorted, the machine either will not POST at all, or it will endlessly reboot.The paperclip trick on the power switch leads can be used to verify if these I don't completely understand the case switch thing jsc, are you saying to try to boot the build using the reset switch in case the power switch is bad? I'll have to use that idea in the future. (Guess your one of us few that installes the cpu and hs while the mb is out of the case). Jack is ALL ears!!! http://dionelabs.com/pc-build/new-computer-troubles.html

You should implement some best practices to reduce the probability of damaging components. With the huge number of different makes and models of PCs out there, specific troubleshooting steps may vary somewhat. If the hard drive light doesn't flash, that is an indicator that it has failed. Go over all of the installation steps in detail and make sure you've completed them properly. http://www.pcworld.com/article/202038/how_to_troubleshoot_your_home_built_pc.html

Pc Build Troubleshooting No Video

Turn on the computer and see if it beeps normally. Boot. Software Section containing a full listing of other general software Q&A's.

Proceed with caution. aevmFeb 6, 2009, 7:53 AM +1 for making this a sticky. If you're confused on where to start, try our free online Mr. Pc Build No Power CH000312 No power or computer does not turn on CH000443 General scanner troubleshooting.

People might not see it unless you put it up top. Pc Build Won't Power On You can also check your motherboard or computer documentation for information on the beep codes. Make sure everything is hunky dory before you close up and put it under your desk or wherever. It was in exactly the right place to create a ground fault in contact with the back of the board.

A system speaker is NOT the same as normal speakers that plug into the back of the motherboard. Newly Built Pc Wont Boot shortstuff_mtMar 8, 2009, 12:56 PM I think it's time for another bump. If you've tried all of that and your PC still doesn't power on when you press the On button, you may have a faulty power supply. Once you solve the problem, throw the page or pages into a folder for future reference.Getting frustrated?

Pc Build Won't Power On

You can also get that information from the manufacturer support page for that model. http://customgamingbuilds.com/troubleshooting-a-new-custom-pc-build/ They are not the target audience for this thread. 1 /4 2 3 4 Next Last Ask a new question Read More Product Hardware Issue Hardware troubleshooting Build Systems Related Resources Pc Build Troubleshooting No Video It lets me test components before I go through the trouble of installing them in a case.If you get the long beeps, add a stick of RAM. Pc Build Turns On But No Display You can either workaround the issue by running the memory in a different slot that does work or replace the motherboard.

This is called "breadboarding" - from the 1920's homebrew radio days. have a peek at these guys To help determine if this is the cause of your issue, try turning the computer on, off, and back on as fast as possible, making sure the computer power light goes I don't want to be responsible for people frying their PSU's shorting out the wrong pins. ... If your mobo has it, use onboard video for initial testing. New Pc Build Powers On Then Off

If good, install the video card and any needed power cables and plug in the monitor. If you have integrated video and a video card, try the integrated video port. shortstuff_mtFeb 6, 2009, 3:29 AM I'm not so sure I buy the "paper clip" trick. check over here Subscribe ▲ Learn more about PCWorld's Digital Editions    🔎 Home News Reviews How-To Video Business Laptops Tablets Phones Hardware Security Software Gadgets Subscribe Resources PCs Phones Printers Ultrabooks

Try one stick of memory in each slot. New Pc Build Not Booting To Bios Reboot the computer and see if anything changes. Love the idea though.

evonguggFeb 12, 2009, 7:29 PM 11.

Forum Search Guidelines Be respectful to others No spam No NSFW content No piracy or key resellers No link shorteners Offensive content will be removed Code of Conduct User Code of Remove any disks or USB devices Remove any disks, CDs, or DVDs that are in the computer. All disk drives should have a data cable and power cable connected to them. Who Introduced The Hard Drive To The Marketplace? Ensure that the main power and the ATX12V connector (a small 4- or 8-pin connector) are both firmly attached.

ProximonMar 30, 2009, 7:10 AM *nod*Not a bad addition now that we'll be seeing more 790GX boards. This is a direct quote from him:"Pull everything except the CPU and HSF. If the system still doesn't work, it's possible that one of your multiple changes may be the new cause of the problem. this content Are there any wires run directly under the motherboard?

Remove new hardware If any new hardware has been recently added to the computer, remove that hardware to make sure it is not the cause of your issue. When they are disconnected, try booting the computer again. of the case doesn't even mention anything if the case is radiator ready. CH001672 How to shut down a computer.

CH001141 How do I fix the Windows blue screen errors? If something isn't working that was working before, ask yourself, what's different? If the system doesn't power up, try swapping the case power and reset switches. Take these steps to find the cause: Firstly check that the main power cable is firmly plugged into a wall socket and into the back of your power supply.

Disconnect all drives If you are unable to diagnose the problem by the beep code (or you do not hear a beep code), power off the computer. See our selection of refurbished desktops and laptops, and check out discounts beyond technology. ir_efremFeb 26, 2009, 12:35 PM I would also like to add that a video card is not needed for a computer to boot. Some motherboards will not boot without detecting that the CPU fan is plugged in to prevent burning up the CPU.14.

Remove the RAM If you continue to experience the same problem with all the above hardware removed, remove the RAM from the motherboard and turn on the computer. If that doesn't work, try removing the existing cable and replacing it with a known working one. Where does it go?" Ans. - The 4 pins closest to the CPU. If your motherboard supports XMP profiles that is the best way to get your RAM running at its rated specs.

CH000396 Divide error.